Comes with USA power supply. 9vDC, center positive, 1200mA. The optional Euro and UK 240V supplies are 500mA and should work ok as the pedal draws a steady 300mA.

You can use a Voodoo Labs pedalpower2+ to power these. You need to use the two LINE6 outputs, with our Analog Man Y-Cable combining them both. Then plug the voodoo labs LINE9 reverse polarity (red) cable between the Y cable and Eventide and you have 9V at 400mA which should work fine. The Y cable and reverse polarity cable are available in our accessories area. Or check out the new Voodoo Labs ISO-5 power supply!! which can power this pedal and many more.

-

Expression pedal control

Eventide Stompboxes will work with any Expression Pedal that is a simple resistive load (potentiometer) with a max value of 25kOhms. For the best performance we recommend the Ernie Ball VP Jr. 25k. Connect the Output to the Eventide Stompbox Expression Pedal Input.

New features in late 2009!!!

ModFactor Update Release Notes
More Presets
ModFactor now supports up to 50 Banks/100 Presets.
This update includes killer new factory presets.
New Chorus Type
A new Chorus algorithm, �Classic,� has been added to the Chorus Type knob.
The Xnob acts as a filter to dial in a wide variety of warmer, vintage style chorus
sounds.
New Phaser Type
A new Phaser algorithm, �PhaseX0,� has been added to the Phaser Type knob.
The Xnob can switch between 2, 4, 6, and 8 Stages to provide a larger
assortment of classic phaser sounds.
Output Level Knob in Rotary
The Rotary Effect now uses the Intensity knob as an output level control.
Expression Pedal Improvements
Expression Pedal Programming Activation:
Expression Pedal programming is now activated only when the Expression Pedal
is at the heel or toe position.
Shorter Timeout:
The Pedal Programming Timeout has been reduced to 2 seconds. This means
that when you move the Expression Pedal to heel or toe position, ModFactor will
allow Expression Pedal programming for 2 seconds and then change to normal
operation.
Pedal Programming Lock
You can now optionally disable live Expression Pedal programming. (See below.)
Parameter Fine-Tuning
The Encoder can now be used to fine-tune all knob parameters if turned within 2
seconds of turning any knob.
Bank Select via Encoder Knob
In Bank Mode, the Encoder can now be used to select banks in either direction if
turned within 2 seconds of pressing a bank change footswitch.
System Menu Updates
[MIDI] � General Improvements have been made to MIDI operation, including
these new MIDI Functions:
[RCV CTL] � There are new choices for Receive Control to alter the unit�s
BYPASS setting:
ACT � Make the unit ACTive, i.e. not bypassed.
TOG � TOGgle the between bypass and active.
[RCV MAP] - BYPASS via Program Change
As well as using MIDI program change to load a preset, now it can also be
programmed to directly control the unit�s BYPASS setting. In the Receive
Map menu you can now select one of the following:
BYP - BYPass the unit
ACT - Make the unit ACTive, i.e. not bypassed.
TOG - TOGgle the between bypass and active.
[CLK IN] - MIDI Input Clock Enable
Turn Encoder to set MIDI Clock Receive ON or OFF. If ON, MIDI Clock is
used as a Tempo source.
[CLK OUT] � MIDI Output Clock Enable
Turn Encoder to set MIDI Clock Transmit ON or OFF. If ON,
ModFactor can now be used as a MIDI Clock source.
[CLK FLT] � MIDI Clock Filter Enable
Turn Encoder to set MIDI Clock Filtering ON or OFF. If ON,
ModFactor can be used with an unstable MIDI Clock source.
[UTILITY] � New Utility Function:
[PDLOCK] - "Lock" Expression Pedal settings
When PDLOCK is set to ON, Expression Pedal programming is disabled
and all Expression Pedal settings are locked. Default is OFF (unlocked).